Home > Water Heater > Why Is My Electric Hot Water Tank Not Working

Why Is My Electric Hot Water Tank Not Working

Contents

Undersized breaker. 6. Also from About.com: Verywell, The Balance & Lifewire InspectAPediaQuestion? Flush Hot Water Heater - How to flush sediment from your water heater. I've left out steps which anyone familiar with electricity knows. check my blog

Action: Fix leaks. Remove covers on water heater see image so you have access to thermostats and elements. 2. Install softener. Listen for sound of running water.How to test and replace TP valve 10) Faulty check valve on recirculation system, or plumbing pipes. http://www.home-repair-central.com/electric-hot-water-heater-troubleshooting.html

My Water Heater Is Not Heating Water

Do make sure the fitting is quite clean before putting in the new element. If the fuse is blown or breaker is tripped, replace the fuse or re-set the circuit breaker. But nothing about the WH will cause the fuse box to over heat.

  1. For these reasons, most homes now need a thermal expansion tank (and a properly adjusted pressure regulating valve).
  2. Overheated wire will cause ECO to trip.
  3. We have no relationship with advertisers, products, or services discussed at this website.
  4. Before you test the elements, check to make sure the circuit breaker is on and not tripped.
  5. A: Try Robertshaw.
  6. The money you contribute helps fund the sites you visit.
  7. First, find the circuit breaker in the main electrical panel that’s labeled for the water heater and switch it off.

If you check, you should have about 240 volts at the terminals on the upper element. That means the lower thermostat isn't working and needs replacement. How to test elements 6) Thermostat set too high. Electric Water Heater Thermostat Also, Right around the heating element gasket, a small amount of water will form a drip or two when the circuit breaker is switched back on, (I'm wondering if this is

Open TP valve and see if water is hot at top of tank. Electric Water Heater Reset Button Flooded water heater 11) Undersized wire from breaker can cause overheated wire, but should trip breaker instead of tank ECO. Element continues heating, and will not turn off.This causes runaway heating, and TP valve will release water or ECO reset will trip, or water will be hotter than usual. However, I didn't hear any knocking this time.

Elements could be bad or going bad too, but before my droning on, it would be best for you to turn off the power, remove both covers and let us know How To Test Water Heater Element Electric Water Heater Thermostat - How to replace a water heater thermostat. ECO will trip when either upper or lower thermostat sticks in ‘on' position causing continuous heating. Inspect wire to tank for damage caused by nail, staple or rat gnaws. 4) Short inside tank: Inspect for burned wires and melting.

Electric Water Heater Reset Button

Not every loose wire will cause ECO to trip, only those that cause upper thermostat to overheat.Action: Replace part connected to burned wire.Test thermostats How to replace thermostats How to replace http://www.whirlpoolwaterheaters.com/owner-center/installation-video-guides/electric-installation-videos-guides/troubleshooting-repair/ Put ear against pipe and listen for running water. My Water Heater Is Not Heating Water Also see our Book Reviews - InspectAPedia. How To Tell If Electric Water Heater Is Working Electric Water Heater Troubleshooting Follow the electric water heater troubleshooting guide below to solve your hot water heater problems.

If you hear it click, than you've reset it. click site See information More info Rare hydrogen build-up in tank after several weeks. Then breaker is loose on busbar 4) Open covers on water heater and inspect for burned, melted parts (read more detail below) Action 1: Check if wires are tightly screwed to If there is power at the circuit breaker, but not at the high limit, check power at the junction box on top of the heater Next place to check is at Gas Water Heater Not Working

Inspect wires inside tank carefully. Thanks for listening. Note: InspectAPedia.com editor Daniel Friedman is a contributing author. news Then check again at 1000 ohms if the meter had shown no reading.

Read steps Use nose to see if circuit breaker smealls burned. Electric Hot Water Heater Not Working After Power Outage Could this be causing the right side (white wire) to be drawing more current? Sign in to make your opinion count.

The element will still be cracked.

Leaking water heater 5) Water leak running hot out of tank. AO Smith was one of the companies and the manufacture date is in the middle of the defect period I have no doubt your dip tube is bad. If the total hot water quantity is small, check first for a bad LOWER heating element. Not Enough Hot Water From Electric Water Heater Replacement heating elements are inexpensive and widely available.

bad power to the heater - test for voltage at the wires coming in to the heater first; if nothing there go to the panel. Occasionally, leaks can be found coming from a fitting (such as around the Temperature and Pressure Relief Valve) or around one of the heating elements. YES Use adequate lighting.YES Wear dry tennis shoes and dry clothes. More about the author In physics, hot water expands and puts pressure on container holding water.

A1: Hello: Is the heater running at about 240 volts? Test wires between tank parts. Photo Credit: Photo by A.Vallecillos / Getty Images Possible CausesBacteria in the tank sediment fed from hydrogen gas created from decay of sacrificial anode. Possible RepairsFlush water heaterUsing a hydrogen peroxide solution You might also enjoy: Sign up There was an error.

Cold and hot water lines are reversed. Tank wattage is element wattage since both elements are never 'on' at same time.See image Power is ON means risk of electrocution which can be sudden, or can take a moment Next question is why did it overheat? Cold water is in tank, and lower themostat is at maximum setting, so lower element should be ON.