Thanks for your help! Obviously, it’s important to be sure this valve works properly. Category Howto & Style License Standard YouTube License Show more Show less Loading... I would have to read through the manufacturers installation instructions. his comment is here
Good luck with your project! Hot water supply valve off immediately. The valve was just replaced but it didn't solve the problem. A couple of months ago, our gas water heater started leaking from the top.
In the video below, Jamie and Adam of the popular television show, MythBusters, show just what can happen when the heat—and resulting pressure—inside a water heater surpasses the water heater's rated It must terminate 6"-12" above the floor, and the end cannot be threaded or have a fitting which permits connecting a plug or cap. Reuben Saltzman 4 YEARS AGO @rolando - You're probably right. We have an Expansion Tank and have noticed that on the pipe leading to it there is a build up of rust.
I can live with a slow leak but how do I fix the current problem? Reuben Saltzman 3 YEARS AGO @Paul DE - thank you for taking the time to come back and post your results here. share|improve this answer edited Feb 13 '13 at 20:45 longneck 12k12549 answered Feb 13 '13 at 19:45 Tester101♦ 98.7k38196391 re: monitoring the pressure, shouldn't the point at which you Hot Water Heater Pressure Relief Valve Keeps Opening Time for a new valve.
I dont want to blow up my house. Also known as- t&p valve (temperature and pressure) valve and tpr valve (temperature pressure relief) valve. No idea about that. http://diy.stackexchange.com/questions/25218/what-causes-a-water-heaters-relief-valve-to-discharge-water I accidentally bumped into the pressure relief valve on my 8 year old hot water heater and water started coming out.
The old hot water heater never leaked. Water Heater Pressure Relief Valve Installation So easy!!! $8 part - Thanks!!! What are your thoughts? to my horror it driping at a fast rate.
And is it safe to reignite the pilot light if water is dripping from the PRV discharge line? Could the PRV be defected on new water heater? Water Heater Pressure Relief Valve Is Releasing Water Charles Says: April 23rd, 2012 at 10:00 pm Tpr valve on hot water heater will leak small amounts of waters from time to time filling a small dish daily, I've replaced Water Heater Pressure Relief Valve Test share|improve this answer answered Feb 13 '13 at 19:58 pdd 2,831517 add a comment| up vote 0 down vote I test the relief valve every six months, when I test smoke
I opened the PRV to let some of the water out, let it go for about a half an hour and then closed it again. this content Tried tape, the plumbers putty then tape going around smoothly 6 times. I would pressume once the level of water in the tank goes down it will stop leaking. I recently replaced the drain valve on my gas water heater. Hot Water Heater Pressure Relief Valve Leaking After Replacement
The PV valve has been replaced and problem has not changed. Reuben Saltzman 3 YEARS AGO @Ahsan - at this point, I think you would do well to have a plumber check it out. If they're not the same, get that corrected. http://stickersweb.com/water-heater/what-to-do-when-water-heater-is-not-working.php Show more Language: English Content location: United States Restricted Mode: Off History Help Loading...
After he's done all work, and turn back the water feed valves, then our hot water tank is starting hissing and leaking. Hot Water Heater Valve Shut Off We installed a brand new Temperature Pressure valve but once connected to the water system problem persist - water leaks. The problem I'm have is that the t&p valve is leaking.
Rino Says: December 19th, 2015 at 1:45 pm Hi, the drain pipe outside is leaking. It ONLY stops dripping when there is hot water being used at home. When you release the lever, it should snap back down. Water Heater Pressure Relief Valve Home Depot Turn off the gas or electricity and cold water supply to the tank.
Thank you so much for this blog! There is an expansion tank installed in the cold water inlet line that sits above the pipe. With deep gratitude, John Al Says: January 21st, 2015 at 11:45 am Am going to replace the valve, there are two to choose from, both have the same pressure specs, but check over here George Says: February 19th, 2011 at 10:08 pm Hi Marc, I have pooling from the inlet fittings on top of my (gas) hot water tank.
I drained the water heater during valve replacement and also learned from the manual TODAY my water heater requires annually the temperature pressure relief value be manually open. elliott 4 YEARS AGO thank you Reuben for helping me and my situation. everything else seems to work fine. Thought is was the outlet (hot water) piping but that was not the case.
I think the relief valve is bad, but I need to ask a question. Should I put the burner back in and relight it? Reuben Saltzman 3 YEARS AGO @Sarah T - It sounds like you have a defective water heater. It was an AO Smith.
It makes sense. Tara Herbert 3 YEARS AGO Dear Mr Saltzman, Your blog is so great. The hot water that comes out of all the faucets in the house also seem hotter than normal. I do have an expansion tank, as in before.
If the new valve is allowing water to leak out you may need to install an expansion tank on the cold water inlet line near your water heater.Expansion tanks are designed Consult the chart at the home center store for proper tank sizing. Reuben Saltzman 3 YEARS AGO Hi Tara, once you have added water to the system, the fill valve should be shut back off, and you shouldn't have to worry about more My dad just changed the t&p valve and it looks like its still filling up with water.
Kris Says: January 8th, 2011 at 3:16 pm Hello.