Home > Water Heater > Water Heater Electric Not Working

Water Heater Electric Not Working

Contents

Action: Look for signs of burning and high heat. I tested it yesterday and it seemed to be functioning properly (sending 230 volts to the upper element and about 48 volts to the lower, then switching to the lower with Smith, "Residential Gas & Electric Water Heatern Service Handbook", A.O. Grounded element. 3. his comment is here

Higher temperatures increase the risk of scalding injuries. Retrieved 3/4/2014, [Copy on file] Carson, Dunlop & Associates Ltd., 120 Carlton Street Suite 407, Toronto ON M5A 4K2. (416) 964-9415 1-800-268-7070 [email protected] Action: Test across top two screws on upper thermostat for 220-240Volts. Repeat on the other screw. http://www.whirlpoolwaterheaters.com/owner-center/installation-video-guides/electric-installation-videos-guides/troubleshooting-repair/

My Water Heater Is Not Heating Water

For thread-in–type elements like we show here, you’ll need a water heater element wrench ($5 at home centers and hardware stores). There is also a slight metallic smell in the water and slight odd taste. ECO shuts off both hot wires in the 240V circuit. I was out of town and just returned today.

  • Action: Read about Stacking 6) Make sure watt rating printed on end of element matches watt rating showing on label located on side of tank. 7) Use nose and eyes to
  • Action: connect ground wire to ground screw at top of tank.
  • Sign in to add this video to a playlist.
  • See next paragraph.
  • Frequently Asked Questions (FAQs) Click to Show or Hide FAQs Please see the electric water heater repair questions & answers now found at ELECTRIC WATER HEATER REPAIR FAQs ...
  • Test across both lower element screws.
  • Bad themostat usually, replace thermostat, then if problem continues then test or replace both elements.

The element will still be cracked. With both thermostat dials set to minimum, I checked the upper thermostat (3 terminal) two left terminals and measured infinite resistance. If you hear a dripping hissing sound at a gas or oil fired water heater typically you're going to find that the bottom of the heater tank is leaking and dripping Gas Water Heater Not Working Shorted wire between parts Test wires Circuit breaker tripped or tripped on one leg.

Clear tank of any sediment first.If elements test OK, check for power at upper electrical upper thermostat. Leaking water heater. Reconnect the wires, making sure the connections are tight. http://www.water-heater-repair-guide.com/electricwaterheatertroubleshooting.html Or if a failed tank will flood belongings or home.

Ground wire must be connected to water heater. ✔Thermostat and element must be covered Cover, insulation and protector are necessary so thermostat can read correct temperature. Electric Hot Water Heater Not Working After Power Outage Remove the water heater's upper access panel. Our thermostat is still set very low so we are surprised and confused. Alan Carson is a past president of ASHI, the American Society of Home Inspectors.

Electric Water Heater Reset Button

But if you see this condition on an electric water heater whose history is unknown, do not assume that this is a current problem. If you hear a hissing sound at an electric water heater that may be "normal" as the electric heating elements are heating up. My Water Heater Is Not Heating Water Carefully remove the insulation and plastic cover. How To Tell If Electric Water Heater Is Working Your Name: Your Message: Send me a copy Send cancel Please wait...

Check thermostats. 3. this content Upon checking, I noticed that the breaker was tripping. Action #3: If action #1 does not show 240Volts, then test wires at top of water heater: Black to Red must test for 240V. Diagram on left: 240V arrives at L1 and L3 screws of upper thermostat <> when ECO is tripped, L1 and L3 screws are hot but electricity stops there. Electric Water Heater Thermostat

Reader follow-up: Also, there was evidence that a short had occurred in lower element region as there were burn marks on or near cover or where there was an electrical malfunction, Never open access panels with the power on. By now, you may already have dealt with your problem, since two or three days is a long time to endure cold water, but if you haven't, the first thing I'd http://stickersweb.com/water-heater/water-heater-not-working-electric.php If the elements are not shorted and there are no other electrical problems you can find, I'd replace the thermostat unit.

Avoid aluminum wire. -Thermostat shorted, causing both elements to be ON at same time. How To Test Water Heater Element Put insulation back over parts. Set lower thermostat to minimum temperature setting.

Is this true?

Clorox is harmful. If you don't have hot water after two hours (water not even warm), first check to make sure the water heater is getting electrical power. This guide is electric water heater specific. Not Enough Hot Water From Electric Water Heater How to replace elements. 4.

and then click off each circuit breaker one at a time to locate which electric circuit is shorting to water pipe. Elements overheat tank. 5. Use nose and eyes to find burned parts. check over here Seems unlikely to fully explain your problem, though, as the localized damage to the fuse-box tells a different story.

About.com Food Health Home Money Style Tech Travel More Autos Dating & Relationships Education Entertainment en Español Careers News & Issues Parenting Religion & Spirituality Sports Share Pin Tweet Submit Stumble The Installation Manual has temperature adjustment instructions for your unit as well as important safety information about scalding. A: It sounds like there may be a leak to ground in one of the elements.