Home > Washing Machine > Water Level Washing Machine Not Working

Water Level Washing Machine Not Working


Then, after about 5 to 20 seconds of this sound, another click and the sound will stop. If you already know how to read a wiring diagram, you can skip this section. Remove the wires from the water level switch and test continuity again. If you test the switch by replacing it, and the problem turns out to be the motor itself, you will probably not be able to return the starting switch for a http://stickersweb.com/washing-machine/washing-machine-water-pump-not-working.php

Take all wires off the component and test resistance across it. The solution is to replace the valve. Figure G-6: Water Level Pressure Tube If the tube or diaphragm is leaking badly, the water level switch will not sense any pressure, and thus will not shut off the water Look at figure G-9.

Washing Machine Water Level Switch

Figure G-4: Fill Strainer Screens When re-installing the hoses, always use new hose washers. Water Level Switch & Pressure Switch & Air Dome Tube Start Your Repair Here We have switches for thousands of models Search Need Help Finding Your Model Number? This prevents a heavy load from being thrown onto the motor suddenly.

Now test between the BR-W and BR terminals. It should be pretty stiff, but if you can't turn it at all, something is locked up. The basket braking arrangement is often a part of the clutch arrangement. Washer Won't Fill With Water The usual solution is to replace the pump.

Braking is usually "fail-safe" — that is, if the solenoid or mechanical arrangement that engages the spin mode fails, the brake will stop the basket automatically. Washing Machine Won't Stop Filling With Water Some newer machines have digital timers and control (computer) boards. And incidental to this, all washers must have a way of controlling water level in the tub, to prevent spillage by overfill or by centrifugal force during the spin cycle. http://www.partselect.com/Repair/Washer/Not-Filling-With-Water/ A good cleaning may be all that’s needed to correct a malfunctioning switch, but continue troubleshooting with the next step. Test the switch for continuity with a volt-ohm meter set at 'OHMS

It controls everything in the cycle. Washing Machine Filling Up With Water But Not Going Through The Cycle If you are unable to fix your washing machine with the information above, enter your model number into the search box for additional repair help. You may see water leaking from, or rust on the top of the solenoid. (See figure G-7A) Since the valves only open during a fill cycle, this may appear as an Water Level Pressure Switch Start Your Repair Here We have switches for thousands of models Search Need Help Finding Your Model Number?

Washing Machine Won't Stop Filling With Water

Thank you for helping make our site better. 1-855-343-0066 Mon-Fri: 7am-1am EST Sat-Sun: 7am-11pm EST 1-888-738-4871 Mon-Fri: 7am-1am EST Sat-Sun: 7am-11pm EST Cart (0) Order Status Home Help Contact Instant Repairman™ This Site Remove power from the appliance before performing this test. Washing Machine Water Level Switch Back to top Please enable cookies. Whirlpool Washer Water Level Switch Troubleshooting What can I do to prevent this in the future?

The power then goes through the violet wire to the water level switch (which must have a LOW water level,) then through the pink wire back into the timer. this content If it still won't start, the motor, starting capacitor or speed selector switch is bad. (The speed selector switch may be trying to start the motor in two different speeds at To test the switch, first fill the tub to the highest water level. It will come to you. Washing Machine Water Level Switch Adjustment

Sometimes it's a broken wire, but more commonly, there will be a problem with the water level switch, timer, lid switch, or temperature switch. If not, this could be one reason why the washing machine spins but won't fill. The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd. weblink If you are at an office or shared network, you can ask the network administrator to run a scan across the network looking for misconfigured or infected devices.

This fill-agitate-fill-agitate cycle will continue for as long as the agitate cycle lasts. Washing Machine Water Level Too Low If it's a common one, your parts dealer may even have a rebuilt one in stock. It should be firmly connected to fittings at each end.Disconnect the tube at each end from the fittings to which it’s attached.

Uploaded on Aug 23, 2011Buy the new Water Level Switch W10337780 http://www.appliancepartspros.com/whi...Follow these simple step-by-step instructions to replace the water level switch on top load direct drive Whirlpool, Kenmore, Sears, Roper,

  1. Figure G-1: Typical Drive Train WASH/RINSE (AGITATION) CYCLE After the water valve closes, an electric motor starts which drives the transmission, sometimes through a belt, and in some cases through a
  2. Inspect the air tube for kinks, breaks or damage.
  3. At the end of the spin cycle, or whenever the lid is lifted, most models have a braking arrangement that stops the tub from spinning.
  4. If not, you’ll need to replace the water level switch.

MORE ABOUT THIS REPAIR - Customers rate this repair as Easy - 30 - 60 minutes We have 40 installation instructions The water level switch is a pressure activated switch that Click here for more details. Figure G-9: Typical Wiring Diagram A few notes about reading a wiring diagram: Notice that in some parts of the diagram, the lines are thicker than in other parts. Washing Machine Keeps Filling With Water When Turned Off Working...

When the motor reverses, the brake locks the basket and the transmission engages, so the agitator agitates. Searching with your model number will give you access to all parts and schematics, symptoms for your specific washer as well as all installation instructions and videos. Figure G-5: Checking Voltage Across Water Solenoid Valve Coils If so, you're getting power to your valve, but it's not opening. check over here Test also between the BR-W and G-Y terminals.

Power will need to be removed from the appliance before attempting this repair. The solution is to replace the dispenser, or if you don't use it any more, plug the hose and seal the cracked dispenser with RTV (silicone seal.) HOSES: Though hose leaks The burning smell comes from the rubber belt, which is riding over the motor pulley or locked pump pulley. theapplianceman 39,012 views 6:14 Washer Water Level Pressure Switch (part #6601ER1006E) - How To Replace - Duration: 4:16.

Generally, the problem will be fairly simple. The switch provides a circuit to supply power to the correct solenoids on the water inlet valve.