Further troubleshooting may be necessary to find the exact part that is malfunctioning. -RRReply 106 Joshua Wazelle February 1, 2016 at 3:42 amI have a Maytag washer and the only thing Your issue could be a number of things. Also check the door strike to ensure that it engages the door lock assembly properly. Andy Trigg (Whitegoodshelp) says March 23, 2015 at 4:14 pm Hello John, if the motor is turning but the drum isn't the belt must be off or slipping. http://stickersweb.com/washing-machine/washing-machine-spin-cycle-not-working-well.php
The drive coupling connects the motor to the transmission and consists of two plastic drive forks with a rubber coupling between them. Have you tried unplugging the washer for 5 minutes? Thanks for the informationReply 135 Lorri January 7, 2016 at 8:02 amFirst, my compliments to you on the fantastic job you do here and the amount of patience you demonstrate when Since we do not have your model number, Google your model number for where the fan is located and how to get at it to check it. -RRReply 25 Clementine Baragry Continued
If you overloaded the washer and try another wash too soon, it may be because the washer motor is thermally protected and it has reset itself until it cools off.Let us MORE ABOUT THIS REPAIR - Customers rate this repair as Easy - 30 – 60 minutes We have 213 installation instructions We have 1 step-by-step video Some top load washers use Email Address Comments: (Oldest first) karen says December 15, 2014 at 9:57 pm Think there is crap in filter its a beko washer just not taking all the water out of We got it replaced and it worked like a dream.Ad ReplyWas this helpful?Helpful?
Check all the wire harnesses to be sure they are all connected secure. When weighing up the cost of encountering further issues with other parts such as the motor or heating element in the near future (As the machine is now 6 years old). If you get a good deal on a used one, go for it, otherwise try something else.Reply 89 CTP February 28, 2016 at 3:03 pmHopefully someone can point me in the Ge Washer Not Spinning Call Whirlpool and they should send someone out.
If your washing machine is displaying any of these symptoms or a door lock fault code has been confirmed, the door lock may need to be replaced. Quick and Easy 5 minute Appliance Fixes 111,741 views 15:01 Washer Not Spinning - Motor Reset - Duration: 3:24. MORE ABOUT THIS REPAIR - Customers rate this repair as Easy - 30 – 60 minutes We have 213 installation instructions We have 1 step-by-step video Some top load washers use
Drive Belt or Spin Belt Start Your Repair Here We have parts for thousands of models Search Need Help Finding Your Model Number?
However, when I turn the transmission pulley, it does turn the inner tub. Maytag Washer Not Spinning The locking mechanism also contains a switch that will indicate to the control board or timer, when the door is locked and therefore allow a spin cycle to operate. A common symptom of a failing motor coupling is that the washing machine fills and drains normally but will not agitate or spin. MORE ABOUT THIS REPAIR - Customers rate this repair as Easy - 30 – 60 minutes We have 35 installation instructions Some front load washing machines use wax motors to engage
I checked the filter and hoses and nothing is blocked and the door lock does work. Your washer is under warranty…Call Whirlpool at… US: 1-866-698-2538 Canada: 1-800-688-2002Hours of Operation: Monday-Friday: 8:00 AM to 8:00 PM ESTLocate the washers model and serial number before calling. -RRReply 116 jemma Washing Machine Wont Spin Or Drain It makes an electrical noise like it's trying to. Kenmore Washing Machine Wont Spin Clutch is new and still in new shape.
It seems like it wants to start spinning, but will stop, it does this 3 times !!Its like is getting stuck with something that is preventing it from spinning !!Reply 36 this content This can be accomplished by determining what the washer is supposed to be doing based on the cycle that it is on. Rating is available when the video has been rented. It could be a fault with the pressure system, or depending on how much water gets pumped away a problem with the pump. Washing Machine Wont Spin Or Agitate
The control board may not be communicating with the washer therefore the washer stops filling with water and just sits. -RRReply 120 Carl G January 23, 2016 at 7:55 pmThank you Copyright © 1999-2016 , Eldis Group Partnership. I leave it for half hour and the next first attempt the manual spin test works fine. weblink Why won't the washing machine spin?
I have tried the spin only at both max and min speeds and again the motor appears to be working but drum movement at all. Washing Machine Spinning But Clothes Still Wet Popular Articles Electrical & Electronics 5 Common Washing Machine Motor Problems 5 Common Washing Machine Motor Problems Electrical & Electronics Clean Up Common Washing Machine Problems Clean Up Common Washing Machine Recently Visited () Menu Ask a Question Share a Post Account SearchSpin Cycle Not Working on Washer0SharePinSaveFollowMoreEmailFlagIt is truly frustrating to have the spin cycle on your washer quit working, leaving
You most likely have a front load washer and the door is locked. It's like it struggling with small/medium/large loads. Have you checked to see if all the wire harnesses are attached behind the control board? Washing Machine Not Spinning Properly Gilbert Arciniega 152,878 views 9:01 Not spinning GE front serviceable washer - Duration: 15:37.
If the shifter becomes even partially defective, the unit may drain the water but not spin. If the plastic tab is broken, the washer may halt during certain cycles. It starts of good from the start it Agitate and spins. http://stickersweb.com/washing-machine/washing-machine-not-working-on-spin-cycle.php The tub will not manually turn.