Home > Ice Maker > Whirlpool Infrared Ice Maker Not Working

Whirlpool Infrared Ice Maker Not Working

Contents

Reply Josh Posted on August 5, 2015 I have a whirlpool the optics seem to be fine since it fills up the ice tray to the proper level then quits making If the door switch does not have continuity when activated, replace it. Made sure it's on first. or any manufacturers or companies listed on this website. http://stickersweb.com/ice-maker/whirlpool-ice-maker-not-working-infrared.php

If the door switch does not have continuity when activated, replace it. If you want to avoid any delay, make sure your PayPal email address is correct. If so remove it, clean all the ice out of it and replace the water inlet valve. About Press Copyright Creators Advertise Developers +YouTube Terms Privacy Policy & Safety Send feedback Try something new!

Whirlpool Ice Maker Reset Button

The first thing you will need to determine is if your refrigerator was made prior to 2002 or if it was made 2002 or later. No- If there is no ice in the mold take that jumper wire and place one end in the hole marked V and the other end in the hole marked L Loading... It is not doing anything.

Shop Parts Repair Help SEARCH Return to previous page Whirlpool Refrigerator Ice Maker Not Working GD5SHAXKQ00 The part(s) or condition(s) listed below for the symptom Refrigerator ice maker not working are If the water inlet valve has sufficient pressure and is getting power, but the ice maker won’t fill with water to make ice, replace the water inlet valve. Subscribe ApplianceAssistant on Youtube! Menu Home Washers Dryers Refrigerators Dishwashers Stoves Videos Manuals Parts Whirlpool In-Door Ice System Troubleshooting Guide Find Ice Maker Repair Parts For general information visit the "How Whirlpool Conquest Ice Maker Not Making Ice Sign in to make your opinion count.

The most co... If the water pressure is sufficient, use a multimeter to check for power to the water inlet valve. It did the same as few days ago and another punchin/shakedown worked. this contact form These are test points to make Whirlpool icemaker repair easy.

One other important note… Whirlpool redesigned the optics portion of this system around 2002 so there are two different diagnostic methods depending on which set of boards are installed in your W10757851 HomeRefrigerator RepairGE Refrigerator Repair GE Washer RepairWhirlpool Washer RepairWasher Repair Dryer RepairDishwasher RepairRange RepairHot Water Heater Appliance Repair BlogRepair VideosProduct Reviews All parts purchased through Appliance-repair-it.com have a 365 day return If you have a thermometer to check temperature just make sure all the food seems to be frozen and everything in the refrigerator seems to be cold and if you are I cannot tell you how happy I was- we had ice!!I just want to thank you (as does my husband) for the information that you made available- the illustrations, the step-by-step

Whirlpool Conquest Ice Maker Not Dispensing Ice

This is because you have to get everything exactly right for it to work. click to read more No questions asked, installed or not! Whirlpool Ice Maker Reset Button Cause 6 Low Water Pressure from House Supply The home may have insufficient water pressure. Whirlpool Conquest Ice Maker Parts I think the part is called the "flipper"?

That is why you should perform the diagnostic tests that we list to see if they are functioning properly. news Language: English (UK) Content location: United Kingdom Restricted Mode: Off History Help Loading... Check the water flow and test the pressure to determine if it is at least 20 psi. Note, that even if the above test passes, there is another test for the optics board to test another function of the optic boards. Kitchenaid Ice Maker Sensor

Reply Ryan Posted on July 16, 2015 Did you replace the optics boards with new OEM replacement part # W10757851? If the door switch fails, the dispenser will not turn on. Reply wahid Posted on May 26, 2015 Hello, Where I can buy mine prt NO 2198586? have a peek at these guys HELP!!!

I can feel frozen ice in the dispenser. Whirlpool Conquest Ice Maker Optics Disconnect the wire harness on the top side and then remove the two Phillips screws to release the emitter control board from the housing.  Re-install the emitter board in the reverse If you realize that it was not current when you confirmed your PayPal contribution, please send me an email ([email protected]) NOTE: Microsoft's Outlook Express is sometimes set not to allow viewing

Sign in to add this to Watch Later Add to Loading playlists...

There are usually test points in the module that a technician can use to further diagnose problems with the module. This should power up the water valve and water should enter the icemaker. The entire repair was very easy to do, and took a minimal amount of time. Whirlpool Infrared Sensor Blinking If the water inlet valve is defective, or if it has insufficient pressure, it won’t allow water to flow through.

Cause 2 Water Inlet Valve The water inlet valve is an electrically-controlled valve that opens to supply water to the dispenser and ice maker. Help. Learn more You're viewing YouTube in English (United Kingdom). http://stickersweb.com/ice-maker/whirlpool-ice-maker-not-working.php How to test this?

AdamDIY 133,521 views 2:01 How to fix whirlpool Ice Maker (PART 1) - Duration: 8:46. Like ApplianceAssistant on Facebook! Thanks for the Ice Maker fix. The rest was cake.

A very simple and easy way to see infrared light by using a digital camera.In the video clip I show you how it works. Parts Water Filter for your Whirlpool Refrigerator RepairClinic Item #4268741 EveryDrop Ice & Water Refrigerator Filter 5 reduces 16 contaminants, including lead and mercury, asbestos, and industrial chemicals. Add to Want to watch this again later? When the thermostat or sensor on the icemaker tray reaches about 15 degrees Fahrenheit, the motor cycles to release the ice cubes.

If you find that the refrigerator is not cooling properly click here Special note for bottom freezers the icemaker may not respond to the jumper wire test described below unless you The other day dumped the ice bin and it hasn't made ice. Perhaps the electrical connections has a frost or moisture corrosion. Check or test each item, starting with the items at the top of the page.