Simply type your model number into the search box below to get started on your appliance parts purchase. First, depending on your model, make sure that the on/off switch is in the on position or the bail arm is in the down position. Reply Ryan Posted on March 20, 2015 It is possible for the ice maker to be bad even if there is ice in the tray. I've tested all the wires for broken connection, I have perfect connection. http://stickersweb.com/ice-maker/whirlpool-ice-maker-not-working-infrared.php
Disconnect the wire harness on the back side and then remove the two Phillips screws to release the receiver control board from the housing. Re-install the receiver board in the reverse MAKE SURE YOUR EMAIL IS CURRENT AND CORRECT IN PAYPAL TO AVOID DELAY ON DELIVERY OF YOUR LOGIN AND PASSWORD. The postings, comments, and opinions are provided at your own risk and do not necessarily represent the views or opinions of AnyoneCanFixIt.com, a division of Absolute Technologies, Inc. First, open the freezer and look on the right-hand side and you should see a blinking light.
No- If there is no ice in the mold take that jumper wire and place one end in the hole marked V and the other end in the hole marked L If this is not the proper email address you want the login and password sent to, please send a note with the proper email address, however, there will be a delay This should power up the water valve and water should enter the icemaker.
This other test is outlined in the instructions available for purchase. Evidently, the infrared beam is now working but I still don't get the indicator LED lights. Or, if you don't use PayPal, then your payment can be sent to: Absolute Technologies, Inc.Attention: Ice Maker RepairPO Box 601Holly Springs, NC 27540 Please include your email address so thatyour W10757851 Reply Denise Posted on February 19, 2015 So it's either a frozen water line, water inlet valve, optic board or a bad ice maker.
An invisible beam of infrared light is sent across the top of the ice bin to detect if the bin is full of ice. Whirlpool In Door Ice Maker Not Working No worry, however, as I now have ice! To access this modular simply remove the cover off the front of the icemaker, note that on some side-by-side refrigerators the icemaker is mounted sideways and you must take the icemaker Just search your model number on our website.
Thanks and have a good day!!John Murphy - [email protected] ICEMAKER REPAIR WORKED!Duane, I have to say I was a little skeptical about buying your icemaker repair guide, however when I saw Kitchenaid Ice Maker Sensor Reply jim Posted on March 20, 2015 When I open the door the optic light blinks twice then close the receiving door on the left side it will stay lite . We cannot express how important it is to read the manufacturers instructions that are included with every product you buy and use. Made sure it's on first.
All rights reserved. http://www.anyonecanfixit.com/icemaker_optics.htm No worry, however, as I now have ice! Whirlpool Ice Maker Reset Button If you are unable to read the attachment that is automatically sent to you once you donate via PayPal (or you do not see an email reply within 10 minutes), try Whirlpool Conquest Ice Maker Not Dispensing Ice I searched the Internet at length for possible how-to repair sites and was fortunate to find yours.
The beam is not visible to the human eye. http://stickersweb.com/ice-maker/whirlpool-gold-conquest-ice-maker-not-working.php Once ice maker powered, if motor contact is bad or intermittent, harvest won't occur. After a while, we heard the IM motor activate but the cubes did not eject into the bin. These are test points to make Whirlpool icemaker repair easy. Whirlpool Conquest Ice Maker Parts
If it is not doing this...then you may be in the middle of a harvest mode by your ice maker (though, this is not likely if your ice maker is not Forum Forum Home New Posts FAQ Calendar Community Albums Member List Forum Actions Mark Forums Read Quick Links Today's Posts Appliance PartsAppliance Maintenance TipsApplianceBlog Home Advanced Search Forum Appliance Repair Talk Thanks Reply Ryan Posted on May 26, 2015 Part number 2198586 is an old part number and it has been replaced with new part number PD00007393. http://stickersweb.com/ice-maker/whirlpool-infrared-ice-maker-not-working.php When I look at the optics beam hole on the left side I do not see any flashing lights, does that mean the control boards are bad or is it the
Board Kit, AP3137510Related Topics:Top Ten Whirlpool and KitchenAid Indoor Icemaker Repair Topics2002 Whirlpool Icemaker - IDI - 3rd unit - need helpIce maker still not working?kenmore ice makerKenmore SxS Model 106.56563400 As soon as you delievered the part to me I had it exchanged and back in the freezer within 10 minutes. I was one of the lucky 5% that did not have to get past Figure 1. Whirlpool Infrared Sensor Blinking Thanks again!Selina Gonzales - [email protected] Note - If Selina could have waited for the delivery of the part (worst case, about 3 days via USPS first class), she could have saved
The bottom mounting bracket on the old icemaker must be reused. $104.13 Quantity: In Stock › Suggested tools Multi Screwdriver RepairClinic Item #3527472 $14.95 Nut Driver RepairClinic Item #3527674 $5.45 Same The temperature should be around 0-10 degrees. Step 3. http://stickersweb.com/ice-maker/whirlpool-gold-ultraease-plus-ice-maker-not-working.php Still no ice….please help the unit is only 2 hrs old.
If you realize that it was not current when you confirmed your PayPal contribution, please send me an email ([email protected]) NOTE: Microsoft's Outlook Express is sometimes set not to allow viewing that covers the front of the ice maker which bolts to the fridge above the ice maker, are they available?