Home > Connect To > Win 2003 Remote Desktop Not Working

Win 2003 Remote Desktop Not Working

Contents

Unfortunately, psShutdown isn't working either. –mrjoshua Jun 15 '09 at 21:23 add a comment| up vote 2 down vote Have you tried accessing the terminal server though a MSTS console switch? Out of the box, Remote Desktop supports two concurrent connections to remotely administer a computer. Can a spellcaster switch between multiple foci? Try accessing the server's services via Computer Management on your desktop and make sure that Terminal Services is up and Running. click site

The command was: shutdown /r /f /t 000 /m \\ or you can use this command to show the GUI for it shutdown /i share|improve this answer answered Jun 15 '09 Error message: Remote Access Cannot Connect 1) Remote access not enabled 2) Remote computer turned off 3) Remote computer not available Additional info: The Server 2012 can RDC OUT. Not the answer you're looking for? So, you grab the Process ID (PID) number from the results and run Tasklist while grep’ing for PID 2252. https://support.microsoft.com/en-us/kb/186645

This Computer Can't Connect To The Remote Computer Server 2003

Also the sfc /scannow does not do anything. You don't need a licensing server for these connections. I thought you were on the right track, but have just tested with an SBS 2003 box I have recently set up here. But not in Server 2012. –Guy Thomas Jun 27 '12 at 13:58 Mabe you need to enable "Remote Desktop" for Domain, Private or Public in "Allow apps to communicate

Figure 1 shows the message he sees. If you don't get an answer in a few hours, I will try to install and test this. –William Hilsum Jun 27 '12 at 9:28 Yes, both on the In the 2012 server manager, it said "Remote Desktop: Enabled". Rdp Tcp Properties Network Adapter Hangs If you want to extend this value, you need CALS as mentioned in my previous reply.By using the console mode ("msdtc/console"), you won't have this restriction but you can only have

Misconfigured Settings Another common scenario is where you're limited in the number of users who can connect simultaneously to a Remote Desktop session or Remote Desktop Services session. Rdp Not Working Server 2008 windows-server-2003 windows-server-2008 remote-desktop share|improve this question asked Jun 27 '09 at 18:06 Kjensen 29851331 I have an odd one that, once I get a writeup done, I'm going post How to connect two parabolic paths in TikZ? T1 to Cisco Router to Static IP on Internet card.

My boss asks me to stop writing small functions and do everything in the same loop Which security measures make sense for a static web site? Windows Server 2012 Remote Desktop Not Working Thanks... If this number is exceeded, additional users who try to connect receive an error message telling them that the server is busy and to try again later. This year I decided to use sysprep and a better server to improve our rollout time.

  • Could the Industrial Revolution be delayed indefinitely?
  • If you can get it, then I would suggest that you upgrade your licensing, you can get more info at http://support.microsoft.com/kb/823313. 0Votes Share Flag Collapse - Reponse To Answer by gechurch
  • it didn't work.
  • How not to lose confidence in front of supervisor?
  • Not the answer you're looking for?
  • I can ping server from "outside" to xxx.xxx.xx9.98 and I get appropriate response.

Rdp Not Working Server 2008

It's important to note that Microsoft does not recommend changing the port assigned to RDP. If you have VSS snapshots, and there are either too many of them or they are taking too much space, RDP can drop you right out. This Computer Can't Connect To The Remote Computer Server 2003 Also, I don't see how this is answering the question stated. –slhck Jul 18 '12 at 16:10 Have you tested your idea on Windows Server 2012? –Guy Thomas Jul This Computer Can't Connect To The Remote Computer Server 2008 Extract result of Reduce when solving an inequalities Advices on start practicing Can a spellcaster switch between multiple foci?

JSI Tip 10169. get redirected here All rights reserved. also simple video driver updates on the server as well.. - Don't re-install the OS that usually isn't needed... If The Co-Signer On My Car Loan Dies, Can The Family Take The Car From Me Like They're Threatening To? The Client Could Not Connect To The Remote Computer

I need workstations to have RDP port set to match NAT - Those match. Unfortunately, such error messages don't always point to a specific root cause. Probably XP does not suport "Network Level Authentication" and when the server requires this, the XP client cannot connect. http://stickersweb.com/connect-to/windows-2003-r2-remote-desktop-not-working.php ip2host, Sep 10, 2009 #2 Vinman Thread Starter Joined: Feb 19, 2005 Messages: 10 I will try the multiple restarts.

share|improve this answer edited Jul 18 '12 at 16:10 slhck 127k38322366 answered Jul 18 '12 at 13:29 sushant 91 Please don't just post links to other sites. Unable To Rdp To Server 2012 Both types of connections were working, now neither is. I can ping the Server with either it's IP address or Computer name.

up vote 4 down vote favorite 1 What are the most common things that will cause a Windows Server 2003/2008 to stop responding to Remote Desktop connections, even though other services

asked 7 years ago viewed 28071 times active 3 years ago Blog How We Make Money at Stack Overflow: 2016 Edition Stack Overflow Podcast #94 - We Don't Care If Bret Then try starting it again from the Services. Email Reset Password Cancel Need to recover your Spiceworks IT Desktop password? Rdp This Computer Can't Connect To The Remote Computer Rollback of the ATI video driver, restart, server restarted much more back to normal, AND my RDP is up and running again!

However, after following the steps posted by sushant (cmd > systempropertiesremote) (which can also be reached by other methods e.g. After I did that all was fine. Not the answer you're looking for? http://stickersweb.com/connect-to/windows-2003-sp2-remote-desktop-not-working.php Thank Wedor!

SBS lets you have two remote desktop connections out of the box (and that's a hard limit - you can't buy terminal services CALs for SBS). 0Votes Share Flag Collapse -